-
Buy productQuick View
[Lsee 3D Printer Control Board]RepRap Arduino-compatible Mother Board 3D Printer Controller remix Board (MEGA2560 + RAMPS 1.4 + A4988))
$150.00Buy productQuick View -
Buy productQuick View
3D Duplicator, GIANTARM® Prusa I3 3D Printer Kit with Assembled Box Controller
3-in-1 3D printer control box
Easy assembly, easy debugging
Reserved design for upgradingBuy productQuick View -
Buy productQuick View
Control board for Alunar 3D Desktop Printer Prusa i3(NOT for HBi3)
3d printer control board
for B018XJ3E02 only
mainboardBuy productQuick View -
Buy productQuick View
Geeetech 3D Printer Control Board GT2560 Support Dual Extruder Power Than ATmega2560 Ultimaker, Ramps
Integrated with the mighty function of the Arduino Mega2560+Ultimaker and Arduino Mega2560+ramps 1.4 kit, The GT2560 can not only take full place the them on respect of both software and hardware, but also features compact size, more convenient connection, and more stable.
Adopt ATmega2560 as the main control chip, coupled with the high-performance USB serial converter FT232RQ.
The main circuit adopts SMD fuse tube, the diode added to the power port can provide reverse protection to the whole circuit, in addition, the 5V USB is USB port protected with 500mA Recoverable fuse.Buy productQuick View -
Buy productQuick View
Geeetech New Melzi 2.0 Complete Reprap 3D Printer Control Board ATMEGA1284p, A4988 for Arduino
Operating voltage: 12v
Main control IC: ATMEGA1284P from ATMEL
FT232RL USB interfaceBuy productQuick View -
Buy productQuick View
Geeetech New Version RepRap Printrboard 3D Printer Control Board (RepRap electronics sets)
Four integrated Allegro A4982 Stepper Drivers
Printrboard is a derivative of Teensylu, an AT90USB1286 development board originally based on Sanguinololu
Four integrated Allegro A4982 Stepper Drivers (no Pololus needed)Buy productQuick View -
Buy productQuick View
Geeetech New Version Single Board Generation 6 Gen6 Electronics for Reprap Plug and Play for FFF/FDM 3D Printers
Generation 6, or Gen6, can be described as a dedicated, Plug-&-Play, single board solution for FFF/FDM 3D Printers.
It is designed to be professionally manufactured, with many small surface mount components, as opposed to Generation 7 which is designed to be printed on a Mendel(among other design goals).
Dimensions 110x60mmBuy productQuick View -
Buy productQuick View
Geeetech Reprap Sanguinololu Rev 1.3a Assembled
1.Supports LCD 2004 module, available for off-line printing.
2. Support multiple power configurations: Main board supplied by 5mm screw terminal, and optional 4pin ATX connector: 7v-12v
3. Adapts Atmel’s ATmega644P – ATmega1284 drop-in compatible. Currently, we use 1284P, the bootloader has been burned before shipping, and users can put it into use after burning the programming code.Buy productQuick View -
Buy productQuick View
Geeetech Rumba 3D Printer Controller Board ATmega2560 for Reprap Prusa Mendel
Use the same CPU as that of Arduino MEGA as main control chip, Atmega2560 cooperates with high-performance USB chip in order that it is compatible with all RAMPS relevant firmware;
Five interfaces as input for temperature sensor.
with extended LCD shield interfaces, supports offline printing( note, SD card slot is not on rumba but on the LCD shield)Buy productQuick View -
Buy productQuick View
Geeetech S-180-12 3D Printer 12V 5A DC Power Supply Box
AC input voltage range?85-264VAC 47-63Hz
Input current: 11V /1.5A, 230V/0.75A
Output: 12V/ 0-15ABuy productQuick View -
Buy productQuick View
Geeetech Stepstick A4988 Stepper Driver Module Compatible with Arduino Mega2560 RepRap Ramps with Translator and Overcurrent Protection
Short-to-ground and shorted-load protection.
Adjustable current control.
Intelligent chopping control.Buy productQuick View -
Buy productQuick View
HICTOP 3D Printer Control Board MKS Base V1.3 RepRap Arduino-compatible Mother Board
Brand : HICTOP
Application : Reprap Prusa I3 3D PrinterBuy productQuick View -
Buy productQuick View
Kuman 3D Printer Controller Kit For Arduino Mega 2560 Uno R3 Starter kits +RAMPS 1.4 + 5pcs A4988 Stepper Motor Driver + LCD 12864 for Arduino Reprap K17
3D Printer Controller Kit Mega 2560 R3
3D Printer Controller RAMPS 1.4,A4988 Stepper Motor Driver
LCD 12864 Graphic Smart Display ControllerBuy productQuick View -
-7%Buy productQuick View
LulzBot Taz 6 Open Source 3D Printer with MatterControl Touch T10 Controller
The Taz 6 is Open Source Hardware allowing you to adapt, modify, and learn from your printer without restriction
MatterControl Touch T10 turns the Taz 6 into a truly independent internet-connected device
Remote Printing – Send models to your printer from anywhere, or transfer models between printersBuy productQuick View -
Buy productQuick View
Lulzbot Taz 6 Platinum Package with Dual Extruder Upgrade and MatterControl Touch Standalone 3D Printer Controller
The Platinum Package includes the LulzBot TAZ 6, LulzBot Dual Extruder, and the MatterControl Touch T10 Controller
Print remotely and use the onboard camera with the MatterControl Touch 10″ Controller
The upgraded Dual Extruder allows you to print with two materials at once including dissolvable support materialsBuy productQuick View -
SaleBuy productQuick View
MatterControl 3D Printer Controller
Plug in your MatterControl Touch, connect via USB to any compatible 3D printer and then follow the simple setup wizard
Sign-in to send and receive print jobs, or download models directly from the web
Simple Setup, Integrated Slicing, Remote Print Monitoring, Automatic Print Leveling, SMS / Email Notifications, Wi-Fi Enabled, Not RequiredBuy productQuick View -
Buy productQuick View
MatterControl Touch – Standalone 3D Printer Controller
Touchscreen controller that turns your 3D printer into a truly independent internet-connected device
Remote Printing – Send models to your printer from anywhere, or transfer models between printers
Onboard Camera – Take a picture of your finished print or check on the status while printingBuy productQuick View -
-3%Buy productQuick View
MatterHackers Ultimachine RAMBo 1.3 3D Printer Controller Kit
This pre-assembled mother board meets all your needs
You will receive all electronic components securely soldered to the PCB
Endstop wires and switches of your choice, and pre-crimped wires…plus much more!Buy productQuick View -
Buy productQuick View
MKS BaseV1.2 3D Printer Controller Board (RAMPS 1.4 + Arduino 2560 remix board)
This board combines and improves the assets of the RAMPS 1.4 and Arduino Mega 2560 boards on a fantastic single board solution
The MKS Base 1.2 board uses a high quality 4-layer PCB which optimizes heat dissipation Firmware can use the same configuration as RAMPS 1.4
The boards supports a wide variety of Stepper Motor DriversBuy productQuick View -
Buy productQuick View
OSOYOO MKS Base V1.4 3D Printer Controller remix Board (MEGA2560 + RAMPS 1.4 + A4982)
This is the combination of Arduino MEGA2560 + RAMPS1.4 + 5 x A4982 drivers
Arduino MEGA compatible Atmega2560 and FT232 processors are compatible with all RAMPS class firmware
Firmware can use the same configuration as RAMPS1.4. It is suitable for dual-Extrude printerBuy productQuick View -
Buy productQuick View
Panucatt Azteeg X3 PRO 3D Printer Controller
The Panucatt Azteeg X3 PRO is a fantastic contoller that provides support for 8 stepper drivers and up to 5 extruders (if you dare)
This controller is very similar to the X3 controller board which is commonly used by 3D printer manufacturers
The X3 PRO is powered by the Atmel ATMEGA2560 micro controller chip and is designed with excellent high current capabilityBuy productQuick View -
Buy productQuick View
Robo 3D R1 PLUS Fully Assembled 3D Printer with MatterControl Touch Controller
Fabricates parts up to 8 x 9 x 10 inches (H x W x D) in size or 720 cubic inches in volume
MatterControl Touch turns the Robo into a truly independent internet-connected device
Remote Printing – Send models to your printer from anywhere, or transfer models between printersBuy productQuick View -
Buy productQuick View
SainSmart 2-in-1 3D Printer Mainboard Controller Panel for RepRap Arduino, Combination of Mega2560 R3 and Ramps 1.4
Accept 24V power supply input
Decrease 1/4 current of the heatbed to solve the heating problem of MOS
Use Marlin software as Ramps 1.4Buy productQuick View -
Buy productQuick View
SainSmart Ramps 1.4 + A4988 + MK2B + Mega2560 R3 + LCD 12864 3D Printer Controller Kit for 3D Printers RepRap
Sainsmart A4988 driver is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil.
Sainsmart Mega2560 R3 is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator. With the bootloader, download the program directly via USB without having to go through other external writer. Supply part of the optional USB power, or as an external power using the AC-to-DC adapter and battery. Arduino development IDE interface is based on open-source principles, allows you to free download for use in project work, school teaching, motor control, interactive works.
Sainsmart LCD 12864 contains a SD-Card reader, an rotary encoder and a 128 Character x 64 Line LCD display. You can easy connect it to your Ramps board using the “smart adapter” included. After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.Buy productQuick View -
Buy productQuick View
XZN Ramps 1.4 Smart Controller LCD12864 Blue Background Version with LED Turn on Control for 3D Printer Reprap Mendel
This LCD controller adds an extra function which is LED backgroud light control circuit to smart controller , with shorting the pins to decide the LED turn on all the time or turn on 30 seconds and than turn off automaticly.
IF you used to start the printing jobs at night and get the parts at the next morning , that means with the new modification, LCD back light will not annoying you any more ,you can make the time of light turn on longer or shorter by adjust the TRIMM R4 100K form 10s to 2mins.
This controller is 100% compaitble with original design.That means you can use the original adpter.Buy productQuick View