-
Buy productQuick View
SainSmart Ramps 1.4 + A4988 + Mega2560 R3 + Endstop + LCD 12864 Kit For RepRap 3D Printer Arduino Mega2560 UNO R3
Sainsmart A4988 driver is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil.
SainSmart Mechanical Endstop perfect for any 3D printer (Including Prusa Mendel i2, Prusa i3, MendelMax, Rostock etc…) also for use on CNC machines and other electronic applications. Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next 3D printer project! Board comes fully assembled and tested.The bare socket is available.
Sainsmart RAMPS 1.4 is a Mega Pololu Shield, or RAMPS for short,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. This board is mostly based on Adrian’s Pololu_Electronics and work by Tonok. Copper etch resists methods suggested by Vik. Also inspired by Vik’s work with EasyDrivers. circuit design based mostly on Adrian’s Pololu_Electronics Joaz at RepRapSource.com supplied initial pin definitions and many design improvements. Much inspiration, suggestions, and ideas from Prusajr, Kliment, Maxbots, Rick, and many others in the RepRap community.Buy productQuick View -
Buy productQuick View
SainSmart Reprap Hot End Hotend V2.0 With 0.5mm &0.4mm nozzle,1.75mm 3D,Mendel For ABS PLA Filament 3D Printer
Aluminum Block Resistor Hotend. Wire Strain Relief.
Easily assembled and torn down with no glue or ceramic
Includes machined aluminum and steel parts, and laser cut wooden parts. Includes pre-crimped wiring.Buy productQuick View -
Buy productQuick View
RioRand(TM) Upgraded 10 pcs 100Kohm NTC Thermistors thermistor,temperture sensor,Reprap,Prusa 3D printer
Powered by RioRand advanced technology
RioRand(TM) 10 x 100Kohm NTC Thermistors thermistor,temperture sensor,Reprap,Prusa 3D printerBuy productQuick View -
-7%Buy productQuick View
LulzBot Taz 6 Open Source 3D Printer with MatterControl Touch T10 Controller
The Taz 6 is Open Source Hardware allowing you to adapt, modify, and learn from your printer without restriction
MatterControl Touch T10 turns the Taz 6 into a truly independent internet-connected device
Remote Printing – Send models to your printer from anywhere, or transfer models between printersBuy productQuick View -
Buy productQuick View
XYZprinting da Vinci Jr. 1.0w 3D Printer (Home Wifi & 2nd Generation Auto-Calibration)
Innovative Auto-Calibration: This 3D printer utilizes a new 9-point calibration detection that adjusts the print bed level along the Z-axis. Just run the calibration test and watch the printer adjust itself!
Wi-Fi Connectivity: Users can send print jobs directly from your Windows or Mac computer or the XYZ app
Compact and Safe: The da Vinci Jr. 1.0w is fully enclosed, lightweight, and built with the safety of you. Though compact, this 3D printer offers a 5.9 x 5.9 x 5.9 inches build volumeBuy productQuick View -
Buy productQuick View
BuildTak 3D Printing Build Surface, 6.5″ x 11.5″ Rectangle, Black (Pack of 3)
Build sheet adheres to a print bed to help the filament stick during printing, while also enabling clean removal of the printed part afterward
Compatible with ABS, PLA, HIPS, PET+, brick, wood, and flexible (TPE) filaments (sold separately)
Durable construction allows for multiple uses with either the same or different filament materialBuy productQuick View -
Buy productQuick View
BuildTak 3D Printing Build Surface, 4.5″ x 4.5″ Square, Black (Pack of 3)
Build sheet adheres to a print bed to help the filament stick during printing, while also enabling clean removal of the printed part afterward
Compatible with ABS, PLA, HIPS, PET+, brick, wood, and flexible (TPE) filaments (sold separately)
Durable construction allows for multiple uses with either the same or different filament materialBuy productQuick View -
Buy productQuick View
Makerbot 0.4mm Head Brass Nozzle for 3D Printer PLA/ABS Printing 3pcs/Pack
Material: brass (copper)
Input Diameter: 1.75mm
Output Diameter: 0.4mmBuy productQuick View -
Buy productQuick View
3rDment PLA 3D Printer Filaments (1.75 mm, Color and Weight vary), Compatible with All FDM 3D Printers – Replicator 2, Ultimaker 1, RepRap, Replicator 2x, Prusa i3, Mendel Prusa, Ultimaker 2, Replicator, Print/bot, Leapfrog Creatr, Zcorp, Solidoodle, UP! Plus, Form 1, Cube X, Up! Mini, Creator, Mende!Max, uPrint, PowerWasp, Dimension, Lulzbot, Felix 2.0
Compatible with the following 3d printers: All FDM 3D Printers – Replicator 2, Ultimaker 1, RepRap, Replicator 2x, Prusa i3, Mendel Prusa, Ultimaker 2, Replicator, Print/bot, Leapfrog Creatr, Zcorp, Solidoodle, UP! Plus, Form 1, Cube X, Up! Mini, Creator, Mende!Max, uPrint, PowerWasp, Dimension, Lulzbot, Felix 2.0, others
High quality – Our latest technology minimize the following : cracks, bubble, blocking of extruder, inaccurate diameter and warp
Environmentally friendly – made with biodegradable materialBuy productQuick View -
Buy productQuick View
HICTOP 3D PLA-1KG Black 1.75mm PLA 3D Printer Filament – 1kg Spool (2.2 lbs) – Dimensional Accuracy +/- 0.05mm
• 1 KG (approximately 2.20 lbs) Spool
• 1.75mm Filament Diameter (Dimensional Accuracy +/- 0.05mm)
• PLA (Polylactic Acid) 3D Printer Filament Vacuumed Sealed With DesiccantBuy productQuick View